IO-Link communication master transceiver IC

Download datasheet Order Direct

Product overview

Description

The L6360 is a monolithic IO-Link master port compliant with PHY2 (3-wire) supporting COM1 (4.8 kbaud), COM2 (38.4 kbaud) and COM3 (230.4 kbaud) modes. The C/QO output stage is programmable: high-side, low-side or push-pull; also cut-off current, cut-off current delay time, and restart delay are programmable. Cut-off current and cut-off current delay time, combined with thermal shutdown and automatic restart, protect the device against overload and short-circuit. C/QO and L+ output stages are able to drive resistive, inductive and capacitive loads. Inductive loads up to 10 mJ can be driven. Supply voltage is monitored and low voltage conditions are detected. The L6360 transfers, through the PHY2 (C/QO pin), data received from a host microcontroller through the USART (IN C/QO pin), or to the USART (OUT C/QI pin) data received from PHY2 (C/QI pin). To enable full IC control, configuration and monitoring (i.e. fault conditions stored in the status register), the communication between the system microcontroller and the L6360 is based on a fast mode 2-wire I2C. The L6360 has nine registers to manage the programmable parameters and the status of the IC. Monitored fault conditions are: L+ line, overtemperature, C/Q overload, linear regulator undervoltage, and parity check. Internal LED driver circuitries, in open drain configuration, provide two programmable sequences to drive two LEDs.

  • All features

    • Supply voltage from 18 V to 32.5 V
    • Programmable output stages: high-side, low-side or push-pull (< 2 Ω)
    • Up to 500 mA L+ protected high-side driver
    • COM1, COM2 and COM3 mode supported
    • Additional IEC61131-2 type 1 input
    • Short-circuit and overcurrent output protection through current limitation and programmable cut-off current
    • 3.3 V / 5 V, 50 mA linear regulator
    • 5 mA IO-Link digital input
    • Fast mode I2C for IC control, configuration and diagnostic
    • Diagnostic dual LED sequence generator and driver
    • 5 V and 3.3 V compatible I/Os
    • Overvoltage protection (> 36 V)
    • Overtemperature protection
    • ESD protection
    • Miniaturized VFQFPN 26L (3.5x5x1 mm) package

Circuit Diagram

You might also like...

All tools & software

    • Part number
      Status
      Description
      Type
      Supplier

      IO-Link Tooling

      Active

      IO-Link development and test tools

      Hardware development tools from partners TEConcept
      IO-Link Tooling

      Description:

      IO-Link development and test tools

      TEConcept USB based IO-Link 1-Port Master

      Active

      Development & debug Tool for IO link device application

      Hardware development tools from partners TEConcept
      TEConcept USB based IO-Link 1-Port Master

      Description:

      Development & debug Tool for IO link device application
    • Part number
      Status
      Description
      Type
      Supplier

      TEConcept IO-Link Master Software Stack

      Active

      IO-Link Master Stack and gateway application (IMS-LSS-DL)

      Embedded software from partners TEConcept
      TEConcept IO-Link Master Software Stack

      Description:

      IO-Link Master Stack and gateway application (IMS-LSS-DL)
    • Part number
      Status
      Description
      Type
      Supplier

      IO-Link Workshop

      Active

      IO-Link Training for Developers, Users and Test Engineers

      Training from partners TEConcept
      IO-Link Workshop

      Description:

      IO-Link Training for Developers, Users and Test Engineers
    • Part number
      Status
      Description
      Type
      Supplier

      STDES-8PH7TMG

      Active

      8-port IO-Link master with TMG stack

      Wired ST
      STDES-8PH7TMG

      Description:

      8-port IO-Link master with TMG stack

      STDES-8PIOLM4P

      Active

      8-port IO-Link master based on IOLM4P L6360

      Wired ST
      STDES-8PIOLM4P

      Description:

      8-port IO-Link master based on IOLM4P L6360

      STEVAL-IDP004V2

      Active

      IO-Link master multi-port evaluation board based on L6360

      Wired ST
      STEVAL-IDP004V2

      Description:

      IO-Link master multi-port evaluation board based on L6360

      STEVAL-IFP016V2

      NRND

      IO-Link communication master transceiver demonstration board based on the L6360

      Process control and automation --
      STEVAL-IFP016V2

      Description:

      IO-Link communication master transceiver demonstration board based on the L6360

      STEVAL-IOM001V1

      Active

      IO-Link master evaluation board based on L6360 equipped with ST morpho connectors for STM32 Nucleo

      Wired ST
      STEVAL-IOM001V1

      Description:

      IO-Link master evaluation board based on L6360 equipped with ST morpho connectors for STM32 Nucleo
    • Part number
      Status
      Description
      Type
      Supplier

      P-NUCLEO-IOM01M1

      Active

      STM32 Nucleo pack for IO-Link master with IO-Link v1.1 PHY and stack

      STM32 ODE Move-Actuate HW --
      P-NUCLEO-IOM01M1

      Description:

      STM32 Nucleo pack for IO-Link master with IO-Link v1.1 PHY and stack

EDA Symbols, Footprints and 3D Models

STMicroelectronics - L6360

Speed up your design by downloading all the EDA symbols, footprints and 3D models for your application. You have access to a large number of CAD formats to fit with your design toolchain.

Please select one model supplier :

Symbols

Symbols

Footprints

Footprints

3D model

3D models

Quality and Reliability

Part Number Marketing Status Package Grade RoHS Compliance Grade Material Declaration**
L6360
Active
VFDFPN 26 3.5x5 Industrial Ecopack2
L6360TR
Active
VFDFPN 26 3.5x5 Industrial Ecopack2

L6360

Package:

VFDFPN 26 3.5x5

Material Declaration**:

PDF

Marketing Status

Active

Package

VFDFPN 26 3.5x5

Grade

Industrial

RoHS Compliance Grade

Ecopack2

L6360TR

Package:

VFDFPN 26 3.5x5

Material Declaration**:

PDF

Marketing Status

Active

Package

VFDFPN 26 3.5x5

Grade

Industrial

RoHS Compliance Grade

Ecopack2

(**) The Material Declaration forms available on st.com may be generic documents based on the most commonly used package within a package family. For this reason, they may not be 100% accurate for a specific device. Please contact our sales support for information on specific devices.

Sample & Buy

Loading...
Swipe or click the button to explore more details Don't show this again
Part Number
Marketing Status
Budgetary Price (US$)*/Qty
Order from ST
Order from distributors
Package
Packing Type
RoHS
Country of Origin
ECCN (US)
ECCN (EU)
L6360
Available at distributors

Distributor availability of L6360

Distributor Name
Region Stock Min. Order Third party link

Distributor reported inventory date:

No availability of distributors reported, please contact our sales office
L6360TR
Available at distributors

Distributor availability of L6360TR

Distributor Name
Region Stock Min. Order Third party link

Distributor reported inventory date:

No availability of distributors reported, please contact our sales office

L6360 Active

Budgetary Price (US$)*/Qty:
-
Package:
Packing Type:
RoHS:
Country of Origin:
ECCN (US):
ECCN (EU):

Part Number:

L6360

Distributor Name

Distributor reported inventory date:

L6360TR Active

Budgetary Price (US$)*/Qty:
-
Package:
Packing Type:
RoHS:
Country of Origin:
ECCN (US):
ECCN (EU):

Part Number:

L6360TR

Distributor Name

Distributor reported inventory date:

Swipe or click the button to explore more details Don't show this again

(*) Suggested Resale Price (USD) per defined quantity for BUDGETARY USE ONLY. For quotes, prices in local currency, please contact your local ST Sales Office or our Distributors