VNH5019A-E

量産中
MySTに保存する

Automotive fully integrated H-bridge motor driver

Download datasheet
Order Direct
概要

製品概要

概要

概要

The VHN5019A-E is a full bridge motor driver intended for a wide range of automotive applications. The device incorporates a dual monolithic high-side drivers and two low-side switches. The high-side driver switch is designed using STMicroelectronics’ well known and proven proprietary VIPower® M0 technology that allows to efficiently integrate on the same die a true Power MOSFET with an intelligent signal/protection circuit.

The three dice are assembled in a MultiPowerSO-30 package on electrically isolated lead-frames. This package, specifically designed for harsh automotive environments offers improved thermal performance thanks to exposed die pads. The input signals INA and INB can directly interface the microcontroller to select the motor direction and the brake condition.

The DIAGA/ENA or DIAGB/ENB, when connected to an external pull-up resistor, enables one leg of the bridge. It also provides a feedback digital diagnostic signal. The CS pin allows to monitor the motor current by delivering a current proportional to its value when CS_DIS pin is driven low or left open. The PWM, up to 20 KHz, lets us control the speed of the motor in all possible conditions. In all cases, a low-level state on the PWM pin turns off both the LSA and LSB switches. When PWM rises to a high-level, LSA or LSB turns on again depending on the input pin state. Output current limitation and thermal shutdown protects the concerned high-side in short to ground condition.

The short to battery condition is revealed by the overload detector or by thermal shutdown that latches off the relevant low-side.

Active VCC pin voltage clamp protect the device against low energy spikes in all configurations for the motor. The CP pin provides the necessary gate drive for an external N-channel PowerMOS used for reverse polarity protection.

  • 特徴

    • AEC-Q100 qualified
    • ECOPACK®: lead free and RoHS compliant
    • Output current: 30 A
    • 3 V CMOS compatible inputs
    • Undervoltage and overvoltage shutdown
    • High-side and low-side thermal shutdown
    • Cross-conduction protection
    • Current limitation
    • Very low standby power consumption
    • PWM operation up to 20 kHz
    • Protection against:
    • Loss of ground and loss of VCC
    • Current sense output proportional to motor current
    • Charge pump output for reverse polarity protection
    • Output protected against short to ground and short to VCC

回路ダイアグラム

ダウンロード

推奨製品

おすすめ製品

TwisterSIM

Dynamic Electro-Thermal simulator for devices in VIPower technology

STEVAL-VNH5019A

VNH5019A Evaluation Board

製品

検索履歴

ブックマーク

Please log in  to show your saved searches.

▼
戻る
戻る
戻る

ご存知でしたか？

Please provide email

Please enter code

Congratulations!

Simple subscription

Congratulations!

x

You can start following this product to receive updates when new Resources, Tools and SW become available. It's easy and takes only 1 minute. ja

You can start following this product to receive updates when new Resources, Tools and SW become available. It's easy and takes only 1 minute. ja

You can start following this product to receive updates when new Resources, Tools and SW become available. It's easy and takes only 1 minute. ja

Invalid code, please check the code sent to your email address and validate again. In case you did not receive any code please select 'I did not receive code'

You can start following this product to receive updates when new Resources, Tools and SW become available. It's easy and takes only 1 minute. ja

お客様のプロフィール情報をSTが処理する方法、及びお客様の個人データ保護の権利を行使する方法について説明した、STのプライバシー･ステートメントをご確認ください。

以下の製品のお知らせを受け取れます
- VNH5019A-E

You can re-use the validation code to subscribe to another product or application.

Sorry, there was a problem on our servers. Please try again.
The current status of a product:
Active: Product is in volume production
Evaluation: Product is under characterization. Limited Engineering samples available
Preview: Product is in design stage
Target: Product is in design feasibility stage.No commitment taken to produce
Proposal: Marketing proposal for customer feedback.No commitment taken to design or produce
NRND: Not Recommended for New Design.Product is in volume production only to support customers ongoing production.Marketing description of the package type.Compliancy of the device with industry requirement domains (IRD)The RoHS status of a product:
ECOPACK 1: Initial grade to identify European RoHS compliant products.
ECOPACK 2: New grade to identify brominated chlorinated and antimony oxide flame retardant free products.
ECOPACK 3: Halogen free RoHS exemptions free products.
(*): ECOPACK 2 version available upon request.
(**): Some versions still existing in ECOPACK 1 or not compliant.The current status of a product:
Active: Product is in volume production
Evaluation: Product is under characterization. Limited Engineering samples available
Preview: Product is in design stage
Target: Product is in design feasibility stage.No commitment taken to produce
Proposal: Marketing proposal for customer feedback.No commitment taken to design or produce
NRND: Not Recommended for New Design.Product is in volume production only to support customers ongoing production.Budgetary PriceMarketing description of the package type.Storage method used to contain product.Main country of assembly or fabrication of the product.ECCNs are five character alpha-numeric designations used on the Commerce Control List to identify dual-use items for export control purposes. ECCNs are five character alpha-numeric designations used on the Commerce Control List to identify dual-use items for export control purposes.The value as specified by level (minTypMax) of the ambient temperature (in Cel) in which this item was designed to operate.The value as specified by level (minTypMax) of the ambient temperature (in Cel) in which this item was designed to operate.