製品概要
概要
This monolithic, high-speed transmitter features 16 independent channels with built-in digital beamforming, that generates 5-Level high voltage pulses (up to ±100 V) suitable to excite multiple channels of an ultrasound transducer.
Each analog channel structure integrates an active RTZ circuit (Clamp) and a T/R switch guaranteeing high OFF isolation between the high-voltage transmitter and the low-voltage receiver when the pulser is transmitting. T/R switches turn ON while receiving echo signals connecting the transducer to the receiver.
Each channels host two independent half bridges (TX0 and TX1) capable of up to ±2A peak output current in 3 or 5 levels configuration. These half bridges can be put in parallel so to provide 3-level profiles up to ±4A current capability on all 16 outputs.
Anti-leakage, anti-memory block, thermal sensors and recirculation current protection features complete the architecture.
Beamforming in ultrasound transmission has traditionally been implemented using analog delay lines. The STHV1600 embeds a digital beamforming mode allowing to program accurate steering of all channels with a resolution as low as 5ns: the signal from each individual transducer element is properly delayed in order to steer the beam in the desired direction.
Both the digital state machine and serial communication interface can be clocked up to 200MHz with differential or rail-to-rail single-ended embedded options.
A generous memory allows to store several patterns to drive output channels with desired code excitation. Suitable registers allow handling of all device operations in the proper sequence and managing device diagnostic features.
Twelve low voltage capacitors are embedded in the package to reduce the external BoM.
STHV1600 is available in a 10mm x 10mm x 1.4mm 144 pins 0.8mm pitch LFBGA package and is specified for operation from 0°C to 80°C.
-
特徴
- 0 to 200 V peak-to-peak output signal
- Up to 30 MHz operating frequency
- Gate driver self-biased architecture; no filtering capacitors required
- Pulsed wave (PW) mode operation:
- 5/3 level output
- ±2 A / ±4 A source and sink current
- Continuous wave (CW) mode operation:
- 150 mW power consumption/channel
- 270 fs RMS jitter (100 Hz-20 kHz)
- -147 dBc/Hz @ 1 kHz phase noise
- Elastography mode operation
- Fully integrated real clamping-to-ground function
- 11 Ω synchronous active clamp
- ±2 A source and sink current
- Fully integrated T/R switch
- 9 Ω ON resistance
- 28 pF parasitic capacitance
- Compliant with receiver multiplexing function
- Auxiliary integrated circuits
- Noise blocking diode function
- Recirculation current protection
- Anti-memory feature
- Thermal protection
- Undervoltage protection and bias supply checks
- Programmable power management to optimize the performance into a probe
- TX Beamforming
- Programmable channels delay for beam-steering and beam-focusing
- Clock frequency up to 200 MHz
- Delay from 0 to 327 µs with 5 ns resolution at 200MHz
- 425 ns minimum delay table writing time
- Embedded volatile memory to store transmission patterns
- 64 kbit (256 rows x 16 bits per channel)
- Waveform compression and repetition algorithm
- Easy driving control
- Device control via serial interface
- Few input signals to drive several devices
- Diagnostic interrupt output
- Single trigger input with anti-glitch to manage TX/RX
- Checksum and parity check
- Very low thermal resistance
- Latch-up free thanks to HV SOI technology
- Only a few passive components required
- differential or rail-to-rail single-ended digital inputs (e.g. LVDS, LVPECL, VML, CML or CMOS)
おすすめ製品
推奨コンテンツ
EDAシンボル / フットプリント / 3Dモデル
STMicroelectronics - STHV1600
Speed up your design by downloading all the EDA symbols, footprints and 3D models for your application. You have access to a large number of CAD formats to fit with your design toolchain.
Please select one model supplier :
EDAシンボル
フットプリント
3Dモデル
品質 & 信頼性
| 製品型番 | マーケティング･ステータス | パッケージ | グレード | RoHSコンプライアンスグレード | 材料宣誓書** |
|---|---|---|---|---|---|
| STHV1600L | 量産中 | LFBGA10X10X1.4 144 12SQ P.8 B.46 | インダストリアル | Ecopack2 |
(**) st.comで提供している材料宣誓書は、パッケージ･ファミリ内で最も一般的に使用されているパッケージに基づく汎用ドキュメントの場合があります。そのため、特定の製品では100%正確ではない可能性があります。特定の製品情報については、セールスサポートまでお問い合わせください
サンプル & 購入
| 製品型番 | 製品ステータス | Budgetary Price (US$)*/Qty | STから購入 | Order from distributors | パッケージ | 梱包タイプ | RoHS | Country of Origin | ECCN (US) | ECCN (EU) | Operating Temperature (°C) (min) | Operating Temperature (°C) (max) | |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| STHV1600L | | | distributors 販売代理店に在庫がない場合は、STのセールス･オフィスまでお問い合わせください |
STHV1600L 量産中
販売代理店に在庫がない場合は、STのセールス･オフィスまでお問い合わせください
（*）概算用の参考価格（US$）です。現地通貨でのお見積りについては、STのセールス･オフィスまたは販売代理店までお問い合わせください。