STM32H757ZI

概要

はじめる

Partner products

セールスブリーフケース

Please enter your desired search query and search again

製品概要

概要

STM32H757xI devices are based on the high-performance Arm^® Cortex^®-M7 and Cortex^®-M4 32-bit RISC cores. The Cortex^®-M7 core operates at up to 480 MHz and the Cortex^®-M4 core at up to 240 MHz. Both cores feature a floating point unit (FPU) which supports Arm^® single- and double-precision (Cortex^®-M7 core) operations and conversions (IEEE 754 compliant), including a full set of DSP instructions and a memory protection unit (MPU) to enhance application security.

STM32H757xI devices incorporate high-speed embedded memories with a dual-bank flash memory of 2 Mbytes, up to 1 Mbyte of RAM (including 192 Kbytes of TCM RAM, up to 864 Kbytes of user SRAM and 4 Kbytes of backup SRAM), as well as an extensive range of enhanced I/Os and peripherals connected to APB buses, AHB buses, 2x32-bit multi-AHB bus matrix and a multi layer AXI interconnect supporting internal and external memory access.

All the devices offer three ADCs, two DACs, two ultra-low power comparators, a low-power RTC, a high-resolution timer, 12 general-purpose 16-bit timers, two PWM timers for motor control, five low-power timers, a true random number generator (RNG), and a cryptographic acceleration cell. The devices support four digital filters for external sigma-delta modulators (DFSDM). They also feature standard and advanced communication interfaces.

特徴
Includes ST state-of-the-art patented technology

Dual core

32-bit Arm^® Cortex^®-M7 core with double-precision FPU and L1 cache: 16 Kbytes of data and 16 Kbytes of instruction cache; frequency up to 480 MHz, MPU, 1027 DMIPS/ 2.14 DMIPS/MHz (Dhrystone 2.1), and DSP instructions

32-bit Arm^® 32-bit Cortex^®-M4 core with FPU, Adaptive real-time accelerator (ART Accelerator) for internal flash memory and external memories, frequency up to 240 MHz, MPU, 300 DMIPS/1.25 DMIPS /MHz (Dhrystone 2.1), and DSP instructions

メモリ

2 Mbytes of flash memory with read-while-write support

1 Mbyte of RAM: 192 Kbytes of TCM RAM (inc. 64 Kbytes of ITCM RAM + 128 Kbytes of DTCM RAM for time critical routines), 864 Kbytes of user SRAM, and 4 Kbytes of SRAM in Backup domain

Dual mode Quad-SPI memory interface running up to 133 MHz

Flexible external memory controller with up to 32-bit data bus: SRAM, PSRAM, SDRAM/LPSDR SDRAM, NOR/NAND flash memory clocked up to 125 MHz in Synchronous mode

CRC calculation unit

セキュリティ

ROP, PC-ROP, active tamper, secure firmware upgrade support, Secure access mode

General-purpose input/outputs

Up to 168 I/O ports with interrupt capability

Reset and power management

3 separate power domains which can be independently clock-gated or switched off:
D1: high-performance capabilities

D2: communication peripherals and timers

D3: reset/clock control/power management

1.62 to 3.6 V application supply and I/Os

POR, PDR, PVD and BOR

Dedicated USB power embedding a 3.3 V internal regulator to supply the internal PHYs

Embedded regulator (LDO) to supply the digital circuitry

High power-efficiency SMPS step-down converter regulator to directly supply V_CORE and/or external circuitry

Voltage scaling in Run and Stop mode (6 configurable ranges)

Backup regulator (~0.9 V)

Voltage reference for analog peripheral/V_REF+

1.2 to 3.6 V V_BAT supply

Low-power modes: Sleep, Stop, Standby and V_BATsupporting battery charging

Low-power consumption

V_BAT battery operating mode with charging capability

CPU and domain power state monitoring pins

2.95 µA in Standby mode (Backup SRAM OFF, RTC/LSE ON)

Clock management

Internal oscillators: 64 MHz HSI, 48 MHz HSI48, 4 MHz CSI, 32 kHz LSI

External oscillators: 4-48 MHz HSE, 32.768 kHz LSE

3× PLLs (1 for the system clock, 2 for kernel clocks) with Fractional mode

Interconnect matrix

3 bus matrices (1 AXI and 2 AHB)

Bridges (5× AHB2-APB, 2× AXI2-AHB)
4 DMA controllers to unload the CPU

1× high-speed master direct memory access controller (MDMA) with linked list support

2× dual-port DMAs with FIFO

1× basic DMA with request router capabilities

Up to 35 communication peripherals

4× I2Cs FM+ interfaces (SMBus/PMBus)

5 USART/UART/LPUART (SPI, ISO 7816, LIN, IrDA, modem)

4 USART/UARTs in SPI mode, 6× SPIs: 3 with muxed duplex I2S audio class accuracy via internal audio PLL or external clock, 1x I2S in LP domain (up to 150 MHz)

4x SAIs (serial audio interface)

SPDIFRX interface

SWPMI single-wire protocol master I/F

MDIO Slave interface

2× SD/SDIO/MMC interfaces (up to 125 MHz)

2× CAN controllers: 2 with CAN FD, 1 with time-triggered CAN (TT-CAN)

2× USB OTG interfaces (1FS, 1HS/FS) crystal-less solution with LPM and BCD

Ethernet MAC interface with DMA controller

HDMI-CEC

8- to 14-bit camera interface (up to 80 MHz)

11 analog peripherals

3× ADCs with 16-bit max. resolution (up to 36 channels, up to 3.6 MSPS)

1× temperature sensor

2× 12-bit D/A converters (1 MHz)

2× ultra-low-power comparators

2× operational amplifiers (7.3 MHz bandwidth)

1× digital filters for sigma delta modulator (DFSDM) with 8 channels/4 filters

Graphics

LCD-TFT controller up to XGA resolution

MIPI DSI host including an MIPI D-PHY to interface with low-pin count large displays

Chrom-ART graphical hardware Accelerator (DMA2D) to reduce CPU load

Hardware JPEG Codec

Up to 22 timers and watchdogs

1× high-resolution timer (2.1 ns max resolution)

2× 32-bit timers with up to 4 IC/OC/PWM or pulse counter and quadrature (incremental) encoder input (up to 240 MHz)

2× 16-bit advanced motor control timers (up to 240 MHz)

10× 16-bit general-purpose timers (up to 240 MHz)

5× 16-bit low-power timers (up to 240 MHz)

4× watchdogs (independent and window)

2× SysTick timers

RTC with sub-second accuracy and hardware calendar

Cryptographic acceleration

AES 128, 192, 256, TDES

HASH (MD5, SHA-1, SHA-2), HMAC

True random number generators

Debug mode

SWD & JTAG interfaces

4-Kbyte embedded trace buffer

96-bit unique ID

All packages are ECOPACK2 compliant
続きを読む一部を表示