M24LR04E-R

NRND
Design Win
MySTに保存する

Dynamic NFC/RFID tag IC with 4-Kbit EEPROM, energy harvesting, I2C bus and ISO 15693 RF interface

Download datasheet
Order Direct

製品概要

概要

The M24LR04E-R device is a Dynamic NFC/RFID tag IC with a dual-interface, electrically erasable programmable memory (EEPROM). The logic scheme is shown in Figure 1.

It features an I2C interface and can be operated from a VCCpower supply. It is also a contactless memory powered by the received carrier electromagnetic wave. The M24LR04E-R is organized as 512 × 8 bits in the I2C mode and as 128 × 32 bits in RF mode.

The M24LR04E-R also features an energy harvesting analog output, as well as a user-configurable digital output pin toggling during either RF write in progress or RF busy mode.

  • 特徴

    • Belonging to ST25 family, which includes all NFC/RF ID tag and reader products from ST
    • I2C interface
      • Two-wires I2C serial interface supports 400 kHz protocol
      • Single supply voltage:
        • 1.8 V to 5.5 V
      • Byte and Page Write (up to 4 bytes)
      • Random and Sequential read modes
      • Self-timed programming cycle
      • Automatic address incrementing
      • Enhanced ESD/latch-up protection
      • I²C timeout
    • Contactless interface
      • ISO 15693 and ISO 18000-3 mode 1 compatible
      • 13.56 MHz ± 7 kHz carrier frequency
      • To tag: 10% or 100% ASK modulation using 1 out of 4 (26 Kbit/s) or 1 out of 256 (1.6 Kbit/s) pulse position coding
      • From tag: load modulation using Manchester coding with 423 kHz and 484 kHz subcarriers in low (6.6 kbit/s) or high (26 kbit/s) data rate mode. Supports the 53 kbit/s data rate with Fast commands
      • Internal tuning capacitance: 27.5pF
      • 64-bit unique identifier (UID)
      • Read Block & Write (32-bit blocks)
    • Digital output pin
      • User configurable pin: RF write in progress or RF busy mode
    • Energy harvesting
      • Analog pin for energy harvesting
      • 4 sink current configurable ranges
    • Temperature range
      • From –40 to 85 °C
    • Memory
      • 4-Kbit EEPROM organized into:
        • 512 bytes in I2C mode
        • 128 blocks of 32 bits in RF mode
      • Write time
        • I2C: 5 ms (max.)
        • RF: 5.75 ms including the internal Verify time
      • Write cycling endurance:
        • 1 million write cycles at 25 °C
        • 150k write cycles at 85 °C
      • More than 40-year data retention
      • Multiple password protection in RF mode
      • Single password protection in I2C mode
      • Package
        • SO8 (ECOPACK2®)
        • TSSOP8 (ECOPACK2®)
        • UFDFPN8 (ECOPACK2®)
    続きを読む 一部を表示

回路ダイアグラム

ダウンロード

eDesignSuite

eDesignSuite is a comprehensive set of easy-to-use design-aid utilities ready to help you streamline the system development process with a wide range of ST products.

Power Management Design Center

Thermal-electrical Simulators for Components

Signal Conditioning Design Tool

NFC/RFID Calculators

Choose design tool:
Power Management Design Center

Power Supply Design Tool

• SMPS design, by topology, by type and by product
• PFC design with analog and digitial control
• Supports various PCB configurations
Choose type:
DC/DC
AC/DC
太陽光発電システム
Power Management Design Center

LED Lighting Design Tool

• Handles AC-DC and DC-DC design in common topologies
• Displays interactive and annotated schematic
• Provides current/voltage graphs, Bode plots, efficiency curves and power-loss data
Choose type:
DC/DC
AC/DC
Power Management Design Center

Digital Power Workbench

• Provides a step-by-step optimized design of power section and control loop
• Generates the STM32Cube embedded software package for custom applications and allows firmware project generation, compatible with multiple STM32 IDEs
Power Management Design Center

Power Tree Designer

• Specify input/output power for each node in the tree
• Check for consistency
• Design each individual node
Choose design tool:
Thermal-electrical Simulators for Components

AC Switches Simulator

• Select ratings and application waveforms
• Get junction temperature and blocking voltage graphs
• Search and sort suitable devices
Thermal-electrical Simulators for Components

Rectifier Diodes Simulator

• Select ratings and application waveforms
• Estimate power losses
• Search and sort suitable devices
Thermal-electrical Simulators for Components

STPOWER Studio

• Supports long mission profiles
• Provides power loss and temperature graphs
• Helps define heatsink thermal properties
Thermal-electrical Simulators for Components

Twister Sim

• Help select the right ViPOWER Automotive power device
• Supports load-compatibility, wiring harness optimization, fault condition impact and diagnostic analysis
• Supports various PCB configurations
Thermal-electrical Simulators for Components

TVS Simulator

• Specify system ratings and surge waveform
• Search and sort suitable devices
Thermal-electrical Simulators for Components

Estimate

• Build simple schematics and firmware inputs in minutes
• Quickly generate reliable estimates of battery life, system power consumption and bill of materials costs
Choose design tool:
Signal Conditioning Design Tool

Active Filters

• Handles multi-stage-designs and common topologies
• Returns circuit component values
• Provides gain, phase and group delay graphs
• Low Pass, High Pass and Band Pass
Signal Conditioning Design Tool

Comparators

• Handles most common configurations
• Returns circuit components values
• Provides I/O signal waveforms
• Inverting, Non Inverting, Window
Signal Conditioning Design Tool

Low side Current Sensing

• Returns circuit component values
• Provides current error graphs
Signal Conditioning Design Tool

High side Current Sensing

• Provides current error graphs.
• Help to select the right High side current sensing and shunt devices.
Choose design tool:
NFC/RFID Calculators

NFC Inductance

• Input geometry and substrate properties
• Get antenna impedance
NFC/RFID Calculators

UHF Link Budget

• Enter forward and reverse link characteristics
• The tool returns link budget estimate
NFC/RFID Calculators

NFC Tuning Circuit

• Enter antenna parameter and matching target
• Select the topology of the matching network
• The tool returns component values for the desired design targets

おすすめ製品

STSW-ST25001

Application executable of the NFC Tap Android app for ST25 product family

STSW-ST25SDK001

Software Development Kit for ST25 Tags and Dynamic Tags

STSW-ST25IOS001

ST25 NFC / RFIDタグ & リーダライタIC製品ファミリ対応iOSアプリ NFC Tapの実行ファイル

EDAシンボル / フットプリント / 3Dモデル

STMicroelectronics - M24LR04E-R

Speed up your design by downloading all the EDA symbols, footprints and 3D models for your application. You have access to a large number of CAD formats to fit with your design toolchain.

Please select one model supplier :

Start your design with UltraLibrarian
Start your design with SamacSys
Symbols

EDAシンボル

Footprints

フットプリント

3D model

3Dモデル

品質 & 信頼性

製品型番 マーケティング･ステータス パッケージ グレード RoHSコンプライアンスグレード 材料宣誓書**
M24LR04E-RDW6T/2
NRND
TSSOP-8L インダストリアル Ecopack2
M24LR04E-RMC6T/2
NRND
UFDFPN 8 2x3x0.6 インダストリアル Ecopack2
M24LR04E-RMN6T/2
NRND
SO8 インダストリアル Ecopack2

M24LR04E-RDW6T/2

Package:

TSSOP-8L

Material Declaration**:

PDF XML
More Info

Marketing Status

NRND

Package

TSSOP-8L

Grade

Industrial

RoHS Compliance Grade

Ecopack2

M24LR04E-RMC6T/2

Package:

UFDFPN 8 2x3x0.6

Material Declaration**:

PDF XML
More Info

Marketing Status

NRND

Package

UFDFPN 8 2x3x0.6

Grade

Industrial

RoHS Compliance Grade

Ecopack2

M24LR04E-RMN6T/2

Package:

SO8

Material Declaration**:

PDF XML
More Info

Marketing Status

NRND

Package

SO8

Grade

Industrial

RoHS Compliance Grade

Ecopack2

(**) st.comで提供している材料宣誓書は、パッケージ･ファミリ内で最も一般的に使用されているパッケージに基づく汎用ドキュメントの場合があります。そのため、特定の製品では100%正確ではない可能性があります。特定の製品情報については、セールスサポートまでお問い合わせください

サンプル & 購入

（*）概算用の参考価格（US$）です。現地通貨でのお見積りについては、STのセールス･オフィスまたは販売代理店までお問い合わせください。

製品

検索履歴

ブックマーク

Please log in  to show your saved searches.

▼
戻る
戻る
戻る

ご存知でしたか？

Please provide email

Please enter code

Congratulations!

Simple subscription

Congratulations!

x

You can start following this product to receive updates when new Resources, Tools and SW become available. It's easy and takes only 1 minute. ja

You can start following this product to receive updates when new Resources, Tools and SW become available. It's easy and takes only 1 minute. ja

You can start following this product to receive updates when new Resources, Tools and SW become available. It's easy and takes only 1 minute. ja

Invalid code, please check the code sent to your email address and validate again. In case you did not receive any code please select 'I did not receive code'

You can start following this product to receive updates when new Resources, Tools and SW become available. It's easy and takes only 1 minute. ja

お客様のプロフィール情報をSTが処理する方法、及びお客様の個人データ保護の権利を行使する方法について説明した、STのプライバシー･ステートメントをご確認ください。

以下の製品のお知らせを受け取れます
- M24LR04E-R

You can re-use the validation code to subscribe to another product or application.

Sorry, there was a problem on our servers. Please try again.